S50 1000A 1MV/A 100A 10mV/A 10A 100mV/A 50mm Output AC Clamp On
Current Transformer Probe with BNC
Clamp-On Current Transformer probe GFUVE® maintains a large
in-stock inventory of Clamp-On Current Transformers probe including
AC, Micro Clamp and Clamp-On CT Accessories for most common
applications. Below is a list of all clamp-on current transformers
available through GFUVE material, however, not all models are
in-stock.
Clamp-On Current Transformer probe are the one-handed operating
solution for temporary energy audits or long-term energy studies.
The GFUVE 1200A Clamp On Current Transformer is specifically
designed to offer broad utility in a compact shape. These CTs
deliver high-accuracy, high-sensitivity, versatility, and low phase
shift.
These clamp on current probe are accessible in different models,
sizes, memories, feeding, and features depending on the
requirements. You can place these precise and efficient clamp on
current probe at your homes, offices, shops, industries, and even
automotive to detect and avoid unnecessary interferences.
The GFUVE clamp probe current transformer is designed for fast and
easy measure the current in industrial and power environments . The
clamp-on core design permits non-contact current measurements
through magnetic field induction without requiring that the primary
wire be taken offline and disconnected for CT installation. This
method permits a safer,easy and portable current measurement.
The round jaw design on the S50 Series AC current clamp on current
transformer probe along with the high content permalloy core makes
them well suited for power quality applications where high accuracy
and low phase shift along with wide frequency are important from
10Hz to 10MHz. Measurement range is 1mA to 1200A. The S50 is a
general purpose 1200A AC current clamp on CT designed for use with
DMMs, power loggers and energy meter calibration instruments that
have a current input. It has a 1000:1 ratio and output of 1mA per
amp or 1mV per amp measured in the jaw. The S50 clamp on CT has an
integral 2.5m lead terminated. The rounded jaw design on this
current clamp makes it well-suited for power applications where
high accuracy 0.1% and low phase shift and wide frequency response
are important. .
APPLICATIONS
- Power meter
- Energy meter
- Load analyzer
- Power quality analyzer(PQA)
- power and harmonic meters
- Phase angle meter
- Energy meter calibrator
- Measuring around cable bundles
- Power load monitoring
- Data logging/recording
- Waveform analysis(oscilloscopes meter)
FEATURES
- Measurement range of 1mA to 1200A AC
- Improved ergonomic design & easy operation
- High content permalloy core
- Frequency 10Hz-10MHz Bandwidth
- Holding wire diameter: φ52mm
- Conforms to EN 61010, 600V CAT III
- High precision 0.1%
- Low phase shift for power measurement
- Designed for DMMs, recorders, loggers, oscilloscopes, power and
harmonic meters
- UL, CE mark
PARAMETERS
| Electrical parameters |
|---|
| Ratio | 1000: 1 , 2000:1, 1000:5 (customized) |
| Accuracy class | 0.1%, 0.2%, 0.5% |
| Primary current | 0 - 500A AC and 0-1000A AC |
| Signal output | 1mV/A, 10mV/A, 100mV/A |
| Secondary voltage | 0 - 0.5V AC and 0 - 1V AC; |
| Secondary current | 0-1A or 0-5A AC |
| Max. Cont. Input current | 1200A |
| Load capacity | ≤4Ω |
| Over voltage category | CAT III 600V |
| Frequency range | 10Hz-10MHz |
| Dielectric strength | 3KV 50Hz/60Hz at 1minute |
| Temperature range | -40°C to +55°C |
| Output | 2.5 meter cable with D01 or BNC connector |
| Max. voltage not insulated conductors | 600 V |
| Standard | EN 61010-1, EN 61010-2-032, IEC60044-1 |
| Installation | clamp type |
| Output mode | lead output(2.5m) |
| Accuracy (1000A Range) | |
|---|
| 0-10A | ≤0.5% |
| 10-100 | ≤0.2% |
| 10-1200A | ≤0.1% |
| Phase Shift(1000A Range) |
|---|
| 0-10A | ≤0.5° |
| 10-100 | ≤0.2° |
| 100-1200A | ≤0.1° |
| Mechanical parameters |
|---|
| Dimensions (L x W x H) (mm) | 105 x 218 x 30 |
| Weight (g) | 650 |
| Holding wire diameter (mm) | φ52 |
| Max. jaw opening (mm) | 52 |
| Jaw color | Red & Grey |
| Material | PC+ABS, UL94 V0 |
Photo
