XQ13 Best Split Core Oscilloscope Clamp On Current Transformer for
Measuring Class 0.1 Output 100mA
Current sensor XQ13-2 Clamp On Current Transformer are designed to
extend the current measuring capabilities of digital multimeters,
power instruments, oscilloscopes, power quality analyzer,
recorders, and other wide range instruments.
Model XQ13-2 Inductive Current Clamp is suitable for 10A-100A cable
online metering.
GFUVE Q8 Series of Clamp-On Current Transformer's are designed for
fast and easy installation. Clamp-On CT uses Permalloy Magnetic
Core or Silicon Amorphous Core, with characteristics of small size.
high precision, good stability and strong anti-interference
ability.
Why Choose GFUVE Current Probes. The Most Comprehensive Line of
Current Probes. GFUVE ® the world's largest supplier, offers
current probe models capable of accurately measuring from the low
µA to kA range. A wide variety of configurations and jaw sizes are
available. Probe types include iron core, Hall Effect, Flux Gate,
and Rogowski etc.
Features
Suitable for 10A-100A cable online measurement.
Holding wire diameter: φ13mm
Dimension: 52.5mm×136.5mm×28mm
Load capacity: ≤4Ω
Installation: clamp type
Output mode: lead output
Applications
Electric energy meter calibrator (on site)
Double clamp type ground resistance tester
Double clamp type phase volt-ampere meter
Digital multi-meter
Multi-function energy meter
Power quality analyzer
Matched instruments
Calibration instrument on site
Parameter
| Electrical parameters |
| Ratio | 1000: 1 or 2000:1 (customized) |
| Accuracy class | 0.1%, 0.2% |
| Primary current | 0 - 100A AC |
| Secondary current | 0 - 100mA AC (customized) |
| Max. Cont. Input current | 120A |
| Over voltage category | CAT III 600V |
| Output signal (AC current) | From 0 to 100mA AC at nominal input current |
| Output signal (AC voltage) | From 0 to 2V AC at nominal input current |
| Frequency range | 40Hz-2000Hz |
| Dielectric strength | 3KV 50Hz/60Hz at 1 minute |
| Temperature range | -20°C to +55°C |
| Output | 2.5 meter cable with D01 connector |
| Max. voltage not insulated conductors | 600 V |
| Standard | EN 61010-1, EN 61010-2-032, IEC60044-1 |
| Installation | Clamp type |
| Output mode | Lead output (2.5m) |
| Mechanical parameters |
| Dimensions (L x W x H) (mm) | 48 x 179 x 27 |
| Weight (g) | 280 |
| Holding wire diameter (mm) | φ13 |
| Max. jaw opening (mm) | 13 |
| Jaw color | Red, yellow, blue, green, black |
| Material | PC+ABS+Polycarbonate, UL94 V0 |
Photos
FAQ, following questions will help you to select the matched probe
for your applications.
1. Please determine if you are measuring AC or DC?
GFUVE XQ13-2 here is for AC measurement. If you are measuring DC,
will have other models like hall effect sensor to suggest.
2. What is the maximum current you will measure?
XQ13-2 max current is 120A
3. What size conductor will you clamp onto? This parameter
determines the probe jaw size needed.
XQ13-2 can clamp conductor with diameter within 13mm
4. What type of probe output do you need or can you work with (mA,
mV, A, AC, etc.)?
XQ13-2 can customize output with mA, mV
5. What is the working voltage of the conductor to be measured?
GFUVE probes should be used below 600 volts
6. What type of termination do you need: jacks, leads or BNC?
XQ13-2 standard has 2.5meter leads. We can offer jacks or BNC… as
options.
7. If you cannot find information you need or would like
assistance, contact us today. We have designed many more probes
than those shown in this catalog, and we manufacture in Beijing,
China.
